|
Post by miles on May 11, 2019 14:27:51 GMT
I would like clarification on the dip switch settings. specifically how to switch from/to Type 1 to Type 2 in the lithium-ion mode. thanks,
|
|
|
Post by Admin on May 14, 2019 15:24:39 GMT
I would like clarification on the dip switch settings. specifically how to switch from/to Type 1 to Type 2 in the lithium-ion mode. thanks, I hope this clarifies things. Attachments:
|
|
|
Post by miles on May 15, 2019 23:40:19 GMT
well i have the book and the 40 amp charger. dip 5 changes from/to lithuim/lead acid. but how do you switch from lithuim profile one to profile two?
|
|
|
Post by miles on May 15, 2019 23:56:56 GMT
thank you. i got an email explaining the book error. (i could not download your pic and zooming was blurry)
|
|
|
Post by ronstory on May 20, 2019 1:28:04 GMT
OK, the manual DC to DC charger is not clear at all at how to the set the voltages.
Are the The S1, S2, S3, S4 settings at the bottom of page 20 and top of the page 21 for Lead acid only? Lead acid is only when S5 is off, correct?
When you set S5 = ON for lithium, if you use any value other then s3 = ON and s4 = ON... then settings in s1 and s2 are ignored?
The manual needs to put the S5 switch setting first in the description, then follow with two tables containing S1-S4, first for lead acid and the next for lithium.
Also, if there a way to set a lithium charge voltage of 13.6V? That is nominal charge voltage for 4 series cells at 3.35 per cell and 13V is too low and 14V is too high.
Thanks, Ron
|
|
|
Post by ronstory on May 20, 2019 1:32:46 GMT
Here is a voltage vs SOC table for typical Lifepo4 batteries.
|
|
|
Post by Ping on May 22, 2019 3:57:19 GMT
Is there an update on this? Seem like a problem. Thanks!
|
|
|
Post by Admin on May 22, 2019 14:01:17 GMT
Is there an update on this? Seem like a problem. Thanks! That is correct, S1/S2 are the boost voltage setting for lead acid mode and S3/S4 are the float settings only when S5 is set to ON S5 is set to OFF for lithium mode, when S5 is OFF and S1 and S2 are set to ON, the unit will exit the Type1 lithium charging settings and go to the Type 2 settings, there is actually a discrepancy on the first chart, Type 2 should be for S1/S2 and not for S3/S4. Down below is a screenshot of how it should be, we will have that updated ASAP. I agree that we should add the S5 settings first before the two table containing the lead acid/lithium charging voltages. I will add that into the revision notes. There is no way to set the litihum charging @ 13.6V, only the charging voltages displayed on the chart. -Renogy Team
|
|
|
Post by bdosborn on May 27, 2019 2:24:07 GMT
Is there an update on this? Seem like a problem. Thanks! Down below is a screenshot of how it should be, we will have that updated ASAP. Can you post the screenshot?
Thanks, Bruce
|
|
|
Post by Admin on Jun 4, 2019 15:36:49 GMT
Down below is a screenshot of how it should be, we will have that updated ASAP. Can you post the screenshot? Thanks, Bruce
See Attached -Renogy Team Attachments:
|
|